KMR02-12 爆炸图及零件
木工雕刻机 · 111 个零件
爆炸图
点击图片放大。
零件清单
勾选所需零件，然后点击下方按钮咨询。
| 选择 | 序号 | 零件编码 | 零件名称 | 备注 |
|---|---|---|---|---|
| 1 | 30021200002 | Cross Recessed Pan Washer Head Tapping Screw ST5×20 | ||
| 2 | 30019900068 | Top Cover | ||
| 3 | 30021200022 | Cross Recessed Pan Head Tapping Screw ST4.2×19 | ||
| 4 | 30023700025 | Bearing Bracket | ||
| 5 | 30115400089 | Motor Housing (Blue) | ||
| 5 | 30215400034 | Motor Housing (DCA) | ||
| 5 | 30115410241 | Motor Housing (东成) | ||
| 5 | 30415400235 | Motor Housing (DongCheng) | ||
| 5 | 30515400218 | Motor Housing (DCK) | ||
| 7 | 30100600049 | Stator | 220V | |
| 7 | 30200600257 | Stator | 220V | |
| 7 | 30400600169 | Stator | 220V | |
| 7 | 30500600106 | Stator | 220V | |
| 7 | 30400600446 | Stator | 127V | |
| 8 | 30016000027 | Baffle Plate | ||
| 9 | 30021600196 | Wave Spring Washer 25 | ||
| 10 | 30021400036 | Ball Bearing 629DD | ||
| 11 | 30016300021 | Insulation Washer | ||
| 12 | 30500400378 | Armature | 220V | |
| 12 | 30200401630 | Armature | 240V | |
| 12 | 30200401690 | Armature | 220V | |
| 12 | 30200401791 | Armature With Bearings | 220V | |
| 12 | 30400401737 | Armature With Bearings | 220V | |
| 12 | 30400401739 | Armature | 220V | |
| 12 | 30100410244 | Armature | 220V | |
| 12 | 30400400932 | Armature | 127V | |
| 13 | 30024000238 | Bearing Retainer | ||
| 14 | 30021400072 | Ball Bearing | ||
| 15 | Sold only as assembly T3 | 仅随组件 T3 供应 | ||
| 16 | 30023400014 | Motor Bracket | ||
| 17 | 30024500021 | Spring (12×1.4×19) | ||
| 18 | 30021300026 | Half Nut M10 | ||
| 19 | 30021200041 | Pan Head Tapping Screw ST5×40 | ||
| 20 | 30020000007 | Collet Nut And Collet Cone Assembly (ID: 12.7) | ||
| 20 | 30020000011 | Collet Nut And Collet Cone Assembly (ID: 12) | ||
| 22 | 30021100053 | Cross Recessed Small Pan Head Screw M6×45 (With Spring And Flat Washer) | ||
| 23 | Sold only as assembly T3 | 仅随组件 T3 供应 | ||
| 24 | 30019900127 | Switch Container | ||
| 25 | 30024500023 | Compression Spring (8.2×0.8×13) | ||
| 26 | 30021500019 | Pin 6 | ||
| 27 | 30024000123 | Circlip for Hole 12 | ||
| 28 | 30116400012 | Pin Cap | ||
| 29 | 30024500019 | Torsion Spring (16.4×1.2×4.8) | ||
| 30 | 30021100051 | Set Screw M10×22 | ||
| 31 | 30024000122 | Locking Lever | ||
| 32 | 30021100057 | Hex Bolt M5×12 | ||
| 33 | 30024000241 | Adjusting Screw 10×90 | ||
| 34 | 30021100233 | Cross Recessed Countersunk Head Screw M4×12 | ||
| 35 | 30021200054 | Pan Head Tapping Screw ST5×75 | ||
| 36 | 30030400017 | Terminal Block | ||
| 37 | 30030800011 | Brush Holder Cap | ||
| 38 | 30030600043 | Carbon Brush | ||
| 39 | 30030700030 | Brush Holder Assembly | ||
| 40 | 30010100031 | Cord Guard (PVC) | ||
| 41 | 30016300005 | Strain Relief | ||
| 42 | 30021200042 | Pan Head Tapping Screw ST4×15 | ||
| 44 | 30030100038 | Switch | 220V | |
| 45 | 30030300450 | Power Cord (British Standard Plug) | 220V | |
| 45 | 30030300064 | Power Cord (European Standard Plug) | 220V | |
| 45 | 30030300485 | Power Cord (Flat Plug) | 220V | |
| 45 | 30030300550 | Brazilian Power Cord | 220V | |
| 45 | 30030300571 | Power Cord (Australian Plug) | 220V | |
| 46 | 30030400055 | Capacitor 0.22μf (Short) | Areas where capacitors and inductors need to be assembled | |
| 47 | 30021200019 | Cross Recessed Pan Head Tapping Screw ST4×18 | ||
| 48 | 30119900002 | Side Cover (Blue) | ||
| 48 | 30219900001 | Side Cover (Green) | ||
| 48 | 30519900030 | Side Cover (DCK) | ||
| 49 | 30019900172 | Plastic Nut | ||
| 50 | 30019900053 | Adjusting Lever | ||
| 51 | 30019900757 | Pole | ||
| 52 | 30024500018 | Spring (12.5×1.6×230) | ||
| 57 | 30021100177 | Wing Screw M5×10 | ||
| 58 | 30019900183 | Chip Deflector | ||
| 59 | 30021100187 | Wing Screw M5×15 | ||
| 60 | 30024500020 | Compression Spring (7.8×0.7×14.5) | ||
| 61 | 30021100054 | Cross Recessed Hex Bolt With Indentation M5×16 | ||
| 62 | 30021300002 | Nut M5 (Non-Standard) | ||
| 63 | 30021100055 | Cross Recessed Hex Bolt With Indentation M5×40 | ||
| 64 | 30021100179 | Slotted Cheese Head Screws With Shoulder M6×26 | ||
| 65 | 30024500022 | Compression Spring (13×1.4×13) | ||
| 66 | 30021100056 | Cross Recessed Hexagon Bolt with Indentation M5×27 | ||
| 67 | 30023000033 | Stopper | ||
| 68 | 30019900249 | Base Plate | ||
| 69 | 30021100229 | Cross Recessed Pan Head Screw M5×10 (With Spring Washer) | ||
| 70 | 30021100052 | Cross Recessed Countersunk Head Screw M4×10 | ||
| 71 | 30009800904 | Base | ||
| 72 | 30010200001 | Rubber Pin (4×9.5) | ||
| 73 | 30021500032 | Locating Pin | ||
| 861 | 30024000240 | Guide Pin | ||
| 862 | 30024000239 | Trimmer Guide | ||
| 863 | 30021100177 | Wing Screw M5×10 | ||
| 864 | 30024000124 | Straight Guide (Type Y) | ||
| 865 | 30025100012 | Wrench 8 | ||
| 866 | 30025100011 | Wrench 24 | ||
| 867 | 30020000008 | Collet Sleeve 1 (ID: 6.35) | ||
| 868 | 30020000009 | Collet Sleeve 2 (ID: 9.52) | ||
| 869 | 30024000125 | Templet Guide | ||
| 870 | 30021100180 | Wing Screw M6×12 | ||
| 871 | Sold only as assembly T2 | 仅随组件 T2 供应 | ||
| 872 | 30019900186 | Fine-Adjusting Screw | ||
| 873 | 30029900113 | Guide Pole For Retainer | ||
| 874 | 30023000034 | Guide Holder | ||
| T1 | 30005090051 | Trimmer Guide Assembly | 包括序号：861, 862, 863 | |
| T2 | 30005090052 | Guide Holder | 包括序号：870, 871, 872, 873, 874 | |
| T3 | 30005090136 | Handle Set | 包括序号：15, 23 | |
| T4 | 30005090053 | Lock Pin Assembly | 包括序号：25, 26, 27, 28 | |
| T5 | 30005090054 | Tightening Screw | 包括序号：29, 30, 31, 32 | |
| T6 | 30005090055 | Base Assembly | 包括序号：57, 59, 60, 61, 62, 63, 64, 65, 66, 67, 68, 69, 70, 71 | |
| T7 | 30020000012 | Collet Sleeve 8 (ID: 8; OD:12.7) | ||
| T7 | 30020000010 | Collet Sleeve 3 (ID: 8; OD:12) | ||
| T7 | 30020000016 | Collet Sleeve (ID: 6; OD:12) |
来源：原厂零件手册（2023.11）。订购时请提供零件编码及序号。